If you have visible lines or âtailsâ at the top and bottom of each pattern, try increasing the pressure in small increments until the edges of the pattern soften.   Start spraying the cabinet doors. Tape and cover box openings and protect walls and ceiling with plastic. Being able to spray at a lower pressure causes less wear and tear on your sprayer and the tip itself. I've never sprayed with a Magnum X7, so I have no idea how much PSI the sprayer produces, or how it performs using these tips. Start and stop the gun after each pass. These tips are the color green and require the use of the blue RAC X tip guard, not the orange one. Anything beyond 4 or 5 wet mils, you're more likely to get orange peel without the right spray tip.
The smaller orifice size of a 210 produces less material and over-spray, which is good for someone with little to no experience spraying. Spray the trim in long, even strokes, keeping the tip about 12 inches from the surface you’re spraying. Does the FFLP 210 and 310 fit on it?Yes, you can use Graco FFLP spray tips with your Magnum X7. These green tips are part of the RAC X series and fit only the blue RAC X tip guard. With your other hand, hold the hose to keep it out of the way. The 310 is awesome for spraying cabinet doors, and I like using the 210 … Having custom cabinets made and plan on spraying them, what paint do you recommend?I sprayed my kitchen cabinets using the Graco X5 airless sprayer and the 517 tip. You'll be spraying between 1,500 and 2,000 PSI for things like cabinets and trim.I have a Graco GX 19 airless sprayer and I am using the fflp tip. If you're spraying in a kitchen, you still need to mask off everything not being painted. You want to set the pressure right to where the spray fan stops fingering.How many gallons sprayed before I have to replace an FFLP tip?The FFLP tips start to become worn and blown out around 20 to 25 gallons.I will be using a Graco Project Painter Plus, which will go to 2800psi with adjustable pressure. You will need to fill in one or both holes and drill new holes where needed.
These are now the only fine finish tips available by Graco.These come with an additional seal (yellow), meant for use when spraying lacquer. Everything you said worked great and was dead on. The FFLP and LP (low pressure) tips have replaced the original green ones, which didn't produce as fine of a finish at lower pressure. Since this project started with a non-flammable, oil-based primer, make sure to flush the sprayer with mineral spirits.
You want just enough pressure so there's no tailing (fingering) on the outer edges of your spray fan but atomized enough to lay down on the surface. If you try to insert an FFLP tip into the Titan tip guard, it won't fit. Then reinstall the hardware and attach the doors and drawers to the cabinets. The right sprayer and proper tip size makes a huge difference with cabinet painting.Matt I just want to give feedback, no questions. Graco claims the over-spray is fifty percent less than the previous green tips, but I'm not sure if the difference is that high.In my experience, these new tips do last longer than the previous ones. Be sure to mark the doors and drawers to each cabinet. The 210 produces a four-inch spray fan, and the 310 a six-inch fan. Would you recommend a 308 tip for polyurethane?Yes, the smaller orifice of the 308 tip will help atomize the poly better and reduce material consumption. If you're using an airless sprayer to spray cabinets, these tips are a must. A good tip size for doors is 310, or 410. You will want to go through this same process with the topcoat material as well. Work within reach. Place the cabinet doors on 2 sawhorses with 2x4 boards, to get them off the ground and up to a comfortable angle for spraying.For best results, prime all the surfaces with a non-flammable, oil-based primer and sealer. You need to use the blue RAC-X tip guard with the green FFLP tips. Can I use that FFLP tip with my X5? So, never point the gun at yourself or anyone else. I am spraying Emerald Urethane with a Graco airless sprayer. The reality of those specs is you almost always have to use a smaller size than what's recommended on the label to get the right results. I followed everything you said here. I get the same finish using the green tips.If you plan on using an airless sprayer to paint cabinets, doors, or trim, the Regardless of the spray tip being used, spraying with an airless sprayer produces over-spray that requires masking in advance. Put on some latex gloves and squeeze out the excess primer. Vacuum … Youâll also want any surfaces you paint to be thoroughly cleaned. Use smaller tip size when applying thinner materials such as stains and enamels; Use larger sizes for thicker materials such as exterior, latex and oil based paints; The larger the size of the tip hole, the faster the material leaves the gun. Also, make sure to caulk gaps between cabinets and walls to create a seamless blend. Now that the cabinets are prepped, prepare the job site. Bubbles formed in the finish because the polycrylic was over-applied. If your project involves painting the room's interior walls it is recommended to paint trim first. Up to 15 times faster, in fact!Perfect for DIY homeowners, fixer-uppers or beginners looking for a fast and easy alternative to brushes and rollers.Just right for DIY homeowners and handymen tackling the small-to-midsize household projects.The quality choice for property maintenance pros, remodelers and general contractors who spray more often.Ensure your paint sprayer always operates at maximum performanceâchoose genuine Graco parts.Painting or staining your cabinets can completely transform the look of your kitchen, bathroom or any room in your house. First sand any damaged areas on the doors or paint cabinet frames with 320-grit sandpaper to remove burrs or ridges, then fill the areas with spackling compound (Photo 3). Lightly sand the doors, drawers and cabinets by moving with the grain of the wood to remove the top layer of finish. also what paint are you using?I spray cabinets with Emerald urethane, using the FFLP spray tips with an airless sprayer. Sand just enough to take off the shine—you don’t need to sand off the finish. You want 60 mesh with enamel, not 100, 200, or 30 mesh. You can even jump down to a 110, but most paint stores don't stock this size, at least my local paint store doesn't.Fresh out of the package, a 210 is perfect for spraying cabinets. Cabinets look like orange peel. The .17 tip size is big.